TE Connectivity Temperature & Humidity Sensor, Digital Output, Surface Mount, Serial-I2C, ±2%RH, 6 Pins
Tekninen dokumentti
Tekniset tiedot
Merkki
TE ConnectivitySensor Function
Temperature & Humidity
Output Type
Digital
Interface Type
Serial-I2C
Accuracy
±2%RH
Mounting Type
Surface Mount
Pin Count
6
Minimum Operating Temperature
-40 °C
Operating Temperature Range
-40 to +125 °C
Maximum Operating Temperature
+125 °C
Minimum Operating Supply Voltage
1.5 V
Maximum Operating Supply Voltage
3.6 V
Package Type
DFN
Length
3mm
Height
0.9mm
Width
3mm
Dimensions
3 x 3 x 0.9mm
Resolution
0.7 %RH
Tuotetiedot
TE Connectivity HTU21D(F) Series Digital Humidity Sensors with Temperature Output
The HTU21D(F) is a digital humidity sensor with temperature output by MEAS. Setting new standards in terms of size and intelligence, it is embedded in a reflow solderable Dual Flat No leads (DFN) package with a small 3 x 3 x 0.9 mm footprint. This sensor provides calibrated, linearized signals in digital, I²C format.
HTU21D(F) digital humidity sensors are dedicated humidity and temperature plug and play transducers for OEM applications where reliable and accurate measurements are needed. Direct interface with a micro-controller is made possible with the module for humidity and temperature digital outputs. These low power sensors are designed for high volume and cost sensitive applications with tight space constraints.
Every sensor is individually calibrated and tested. Lot identification is printed on the sensor and an electronic identification code is stored on the chip – which can be read out by command. Low battery can be detected and a checksum improves communication reliability. The resolution of these digital humidity sensors can be changed by command (8/12bit up to 12/14bit for RH/T).
With MEAS’ improvements and miniaturization of this sensor, the performance-to-price ratio has been improved – and eventually, any device should benefit from its cutting edge energy saving operation mode.
Temperature & Humidity Sensors, TE Connectivity
Ideoi. Luo. Tee yhteistyötä
LIITY ILMAISEKSI
Ei piilokuluja!
- Lataa ja käytä DesignSpark-ohjelmistoamme piirilevyjen ja 3D-mekaniikan suunnitteluun.
- Selaa ja osallistu nettisivujen sisältöön ja keskusteluihin.
- Lataa 3D-malleja, piirustuksia ja pohjakuvia yli miljoonasta tuotteesta.
Varastotiedot eivät ole tilapäisesti saatavilla.
Tarkista myöhemmin uudelleen.
€ 3,20
kpl (ilman ALV)
€ 4,02
kpl (Sis ALV:n)
Standardi
1
€ 3,20
kpl (ilman ALV)
€ 4,02
kpl (Sis ALV:n)
Standardi
1
Ideoi. Luo. Tee yhteistyötä
LIITY ILMAISEKSI
Ei piilokuluja!
- Lataa ja käytä DesignSpark-ohjelmistoamme piirilevyjen ja 3D-mekaniikan suunnitteluun.
- Selaa ja osallistu nettisivujen sisältöön ja keskusteluihin.
- Lataa 3D-malleja, piirustuksia ja pohjakuvia yli miljoonasta tuotteesta.
Tekninen dokumentti
Tekniset tiedot
Merkki
TE ConnectivitySensor Function
Temperature & Humidity
Output Type
Digital
Interface Type
Serial-I2C
Accuracy
±2%RH
Mounting Type
Surface Mount
Pin Count
6
Minimum Operating Temperature
-40 °C
Operating Temperature Range
-40 to +125 °C
Maximum Operating Temperature
+125 °C
Minimum Operating Supply Voltage
1.5 V
Maximum Operating Supply Voltage
3.6 V
Package Type
DFN
Length
3mm
Height
0.9mm
Width
3mm
Dimensions
3 x 3 x 0.9mm
Resolution
0.7 %RH
Tuotetiedot
TE Connectivity HTU21D(F) Series Digital Humidity Sensors with Temperature Output
The HTU21D(F) is a digital humidity sensor with temperature output by MEAS. Setting new standards in terms of size and intelligence, it is embedded in a reflow solderable Dual Flat No leads (DFN) package with a small 3 x 3 x 0.9 mm footprint. This sensor provides calibrated, linearized signals in digital, I²C format.
HTU21D(F) digital humidity sensors are dedicated humidity and temperature plug and play transducers for OEM applications where reliable and accurate measurements are needed. Direct interface with a micro-controller is made possible with the module for humidity and temperature digital outputs. These low power sensors are designed for high volume and cost sensitive applications with tight space constraints.
Every sensor is individually calibrated and tested. Lot identification is printed on the sensor and an electronic identification code is stored on the chip – which can be read out by command. Low battery can be detected and a checksum improves communication reliability. The resolution of these digital humidity sensors can be changed by command (8/12bit up to 12/14bit for RH/T).
With MEAS’ improvements and miniaturization of this sensor, the performance-to-price ratio has been improved – and eventually, any device should benefit from its cutting edge energy saving operation mode.
Temperature & Humidity Sensors, TE Connectivity
Ideoi. Luo. Tee yhteistyötä
LIITY ILMAISEKSI
Ei piilokuluja!
- Lataa ja käytä DesignSpark-ohjelmistoamme piirilevyjen ja 3D-mekaniikan suunnitteluun.
- Selaa ja osallistu nettisivujen sisältöön ja keskusteluihin.
- Lataa 3D-malleja, piirustuksia ja pohjakuvia yli miljoonasta tuotteesta.