Diodes Inc Fixed Shunt Voltage Reference 3V ±1.0 % 3-Pin SOT-23, LM4040D30FTA

RS tilauskoodi: 165-8407Tuotemerkki: DiodesZetexValmistajan osanumero.: LM4040D30FTAIMPA: 0
brand-logo
Näytä kaikki Voltage References tuotteet

Tekninen dokumentti

Tekniset tiedot

Reference Type

Fixed

Pin Count

3

Minimum Operating Temperature

-40 °C

Mounting Type

Surface Mount

Topology

Shunt

Maximum Operating Temperature

+125 °C

Nominal Voltage

3V

Initial Accuracy

±1.0 %

Width

1.4mm

Height

1.02mm

Maximum Output Current

15mA

Length

3.04mm

Package Type

SOT-23

Dimensions

3.04 x 1.4 x 1.02mm

Alkuperämaa

China

Tuotetiedot

Tubular

Low Voltage Lighting Transformers

Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.

Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.

Ideoi. Luo. Tee yhteistyötä

LIITY ILMAISEKSI

Ei piilokuluja!

design-spark
design-spark
  • Lataa ja käytä DesignSpark-ohjelmistoamme piirilevyjen ja 3D-mekaniikan suunnitteluun.
  • Selaa ja osallistu nettisivujen sisältöön ja keskusteluihin.
  • Lataa 3D-malleja, piirustuksia ja pohjakuvia yli miljoonasta tuotteesta.
Klikkaa tästä saadaksesi lisätietoja

Varastotiedot eivät ole tilapäisesti saatavilla.

Tarkista myöhemmin uudelleen.

Varastotiedot eivät ole tilapäisesti saatavilla.

€ 0,228

1 kpl (3000 kpl/kela) (ilman ALV)

€ 0,283

1 kpl (3000 kpl/kela) (Sis ALV:n)

Diodes Inc Fixed Shunt Voltage Reference 3V ±1.0 % 3-Pin SOT-23, LM4040D30FTA

€ 0,228

1 kpl (3000 kpl/kela) (ilman ALV)

€ 0,283

1 kpl (3000 kpl/kela) (Sis ALV:n)

Diodes Inc Fixed Shunt Voltage Reference 3V ±1.0 % 3-Pin SOT-23, LM4040D30FTA
Varastotiedot eivät ole tilapäisesti saatavilla.

Ideoi. Luo. Tee yhteistyötä

LIITY ILMAISEKSI

Ei piilokuluja!

design-spark
design-spark
  • Lataa ja käytä DesignSpark-ohjelmistoamme piirilevyjen ja 3D-mekaniikan suunnitteluun.
  • Selaa ja osallistu nettisivujen sisältöön ja keskusteluihin.
  • Lataa 3D-malleja, piirustuksia ja pohjakuvia yli miljoonasta tuotteesta.
Klikkaa tästä saadaksesi lisätietoja

Tekninen dokumentti

Tekniset tiedot

Reference Type

Fixed

Pin Count

3

Minimum Operating Temperature

-40 °C

Mounting Type

Surface Mount

Topology

Shunt

Maximum Operating Temperature

+125 °C

Nominal Voltage

3V

Initial Accuracy

±1.0 %

Width

1.4mm

Height

1.02mm

Maximum Output Current

15mA

Length

3.04mm

Package Type

SOT-23

Dimensions

3.04 x 1.4 x 1.02mm

Alkuperämaa

China

Tuotetiedot

Tubular

Low Voltage Lighting Transformers

Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.

Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.

Ideoi. Luo. Tee yhteistyötä

LIITY ILMAISEKSI

Ei piilokuluja!

design-spark
design-spark
  • Lataa ja käytä DesignSpark-ohjelmistoamme piirilevyjen ja 3D-mekaniikan suunnitteluun.
  • Selaa ja osallistu nettisivujen sisältöön ja keskusteluihin.
  • Lataa 3D-malleja, piirustuksia ja pohjakuvia yli miljoonasta tuotteesta.
Klikkaa tästä saadaksesi lisätietoja